- Audio connections<\/strong><\/a><\/li>
- External hardware<\/strong><\/a><\/li>
- Computer<\/a><\/strong><\/li><\/ul><\/li><\/ol>\n\n\n\n
IMPORTANT<\/strong>: You must register your Behringer RD-9 within the first 90 days of purchase to receive the three-year extended warranty.<\/p>\n\n\n\n
Register the RD-9<\/h2>\n\n\n\n
Before we dive in, you will first need to register the RD-9 with Behringer. You will get a free three-year extended warranty when you register the device. <\/p>\n\n\n\n
Follow the instructions in our SweetCare guide: How to Register your Behringer to Get the Full Warranty<\/a>.<\/p>\n\n\n\n
<\/div>RD-9 setup and connections<\/h2>\n\n\n\n
The RD-9\u2019s TRS audio outputs can easily connect to an audio interface or mixer, and you can transmit MIDI data over the USB connection or MIDI ports. This makes it easy to integrate with other hardware devices or record a MIDI performance. You can also synchronize other hardware synthesizers and sequencers with MIDI or external analog clocks.<\/p>\n\n\n\n
![\"back](\"https:\/\/www.sweetwater.com\/sweetcare\/media\/2022\/03\/back-of-RD9.jpg\")
<\/figure>\n\n\n\nAudio connections<\/h3>\n\n\n\n
There are three primary audio connections: Headphones (stereo), Mono (main), and Return. The Headphone output is stereo, while the Mono output is mono. The Return connector is an input and also mono and can be used to return an external signal back into the main output.
<\/p>\n\n\n\n- The Return is an input that can be used to return an individual voice or voices that are processed externally like an external reverb, EQ, or compressor unit. This input sums with the Main output.<\/li>
- All Voice outputs are unbalanced<\/a> signals.<\/li>
- Use the Trigger Out jacks to send +5V 2ms pulses to trigger output devices. Trigger 1 is Rimshot<\/strong>, Trigger 2 is Clap<\/strong>, and Trigger 3 is BD Assignable<\/strong>.
- <\/li><\/ul><\/li><\/ul>\n\n\n\n
External hardware<\/h3>\n\n\n\n
You can incorporate the RD-9 with external synths and sequencers in a few ways. One is with the \u215b-inch (3.5mm) Clock IN and OUT jacks. Another way is with MIDI, which is helpful, especially when using a MIDI interface for DAW synchronization. Another method is via the three different \u00bc-inch Trigger OUTs.<\/p>\n\n\n\n
Sync IN\/OUT<\/h4>\n\n\n\n
IMPORTANT: <\/strong>Do not overload the \u215b-inch SYNC IN input. The input accepts a maximum incoming voltage of +15 V, and the SYNC OUT outputs should be connected to \u215b-inch inputs capable of receiving the +5 V output voltage. Overloading the RD-9 may result in damage to the unit and will require non-warranty repair.<\/p>\n\n\n\n
The \u215b-inch Sync IN and OUT jacks send and receive PPQ<\/a> (pulses per quarter), which is used for sequencing and automation. If you want the RD-9 to control external hardware via analog clock (using the RD-9 as the primary device), use a \u215b-inch cable and connect it from the Sync OUT of the RD-9 to the Sync IN of the external hardware.<\/p>\n\n\n\n
On the other hand, if you want the external hardware to control the RD-9 (RD-9 as the secondary device), use a \u215b-inch cable and connect the external hardware\u2019s Sync OUT to the RD-9\u2019s Sync IN.<\/p>\n\n\n\n
Changing the PPQ<\/h4>\n\n\n\n
There may be a time when the tempo, time, or pitch sound slightly off. This could be because the PPQ of the device you\u2019ve connected doesn\u2019t match that of the RD-9. By default, the RD-9\u2019s PPQ is set to 24. To change it, you\u2019ll need to go into the CLOCK Settings<\/strong>.<\/p>\n\n\n\n
- Press the Settings <\/strong>button, then press the 3 <\/strong>step button to access the CLOCK <\/strong>settings.<\/li>
- Press the TAP\/HOLD <\/strong>button until you see Analog Clk Mode<\/em>, then use the DATA <\/strong>knob to change the PPQ amount.<\/li><\/ol>\n\n\n\n
MIDI<\/h4>\n\n\n\n
Another great way to incorporate the Behringer RD-9 in your rig is through MIDI. MIDI will also send and receive note information similar to the SYNC I\/O, which sends and receives the clock and stop\/start samples. <\/p>\n\n\n\n
By default, the RD-9 is set to MIDI Ch. 1. If the external hardware that\u2019s connected is also set to MIDI Ch. 1, that will be triggered too. If you want the RD-9 to be on its own MIDI channel, you\u2019ll need to go to the MIDI settings. <\/p>\n\n\n\n
- Press the Settings <\/strong>button, then press the 1 <\/strong>step button to access the MIDI <\/strong>settings.<\/li>
- Use the encoder knob to change the MIDI channel.
- Press the TAP\/HOLD <\/strong>button once to change the MIDI OUT channel.<\/li><\/ol>
- Press the TAP\/HOLD <\/strong>button twice to enable FORWARD to USB<\/em>, which sends the MIDI output to the USB out.<\/li><\/ol>
- Press the TAP\/HOLD <\/strong>button three times to turn on SOFT THRU<\/em>. Turning this on will disable the MIDI OUT and turn it into a second THRU device.<\/li><\/ol>
- Press the TAP\/HOLD <\/strong>button four times to set the Device ID. This is particularly useful when working with SysEx.<\/li><\/ol><\/li><\/ol>\n\n\n\n
Computer<\/h3>\n\n\n\n
The Behringer RD-9 can also be connected to your computer using a USB cable. This allows you to record in your DAW and use the SYNTHTRIBE app<\/a> to save and load presets and update your firmware. You can also send MIDI out from your computer to your RD-9. To update your MIDI settings, follow these steps.<\/p>\n\n\n\n
- Press the Settings <\/strong>button, then press the 2 <\/strong>step button to access the USB <\/strong>settings.<\/li>
- Use the encoder knob to select the USB MIDI channel (1-16, All, Out) for the incoming USB MIDI signal.<\/li>
- Press the TAP\/HOLD <\/strong>button once, then use the encoder knob to change the MIDI OUT channel.<\/li>
- Press the TAP\/HOLD <\/strong>button twice, then use the encoder knob to enable Forward to MIDI.<\/em> This will send the MIDI output of the RD-9 to the USB OUT.
- A data loop may occur if using both a MIDI interface and audio interface at the same time.<\/li><\/ol><\/li><\/ol>\n\n\n\n
My computer isn’t recognizing the RD-9!<\/h4>\n\n\n\n
If your RD-9 isn\u2019t being recognized by a computer, try a different USB port and USB cable. If that doesn\u2019t work, check out our article on resolving MIDI device issues in PC and Mac<\/strong><\/a>. <\/p>\n\n\n\n
- Press the Settings <\/strong>button, then press the 2 <\/strong>step button to access the USB <\/strong>settings.<\/li>
- Press the TAP\/HOLD <\/strong>button four times to set the Device ID. This is particularly useful when working with SysEx.<\/li><\/ol><\/li><\/ol>\n\n\n\n
- Press the TAP\/HOLD <\/strong>button three times to turn on SOFT THRU<\/em>. Turning this on will disable the MIDI OUT and turn it into a second THRU device.<\/li><\/ol>
- Press the TAP\/HOLD <\/strong>button twice to enable FORWARD to USB<\/em>, which sends the MIDI output to the USB out.<\/li><\/ol>
- Use the encoder knob to change the MIDI channel.
- Press the TAP\/HOLD <\/strong>button until you see Analog Clk Mode<\/em>, then use the DATA <\/strong>knob to change the PPQ amount.<\/li><\/ol>\n\n\n\n
- Press the Settings <\/strong>button, then press the 3 <\/strong>step button to access the CLOCK <\/strong>settings.<\/li>
- Use the Trigger Out jacks to send +5V 2ms pulses to trigger output devices. Trigger 1 is Rimshot<\/strong>, Trigger 2 is Clap<\/strong>, and Trigger 3 is BD Assignable<\/strong>.
- External hardware<\/strong><\/a><\/li>