{"id":1770048,"date":"2021-07-16T13:11:55","date_gmt":"2021-07-16T13:11:55","guid":{"rendered":"https:\/\/www.sweetwater.com\/sweetcare\/?post_type=articles&p=1770048"},"modified":"2026-04-20T14:57:57","modified_gmt":"2026-04-20T18:57:57","slug":"behringer-x-dante-setup-guide","status":"publish","type":"articles","link":"https:\/\/www.sweetwater.com\/sweetcare\/articles\/behringer-x-dante-setup-guide\/","title":{"rendered":"Behringer X-DANTE Setup Guide"},"content":{"rendered":"\n

In this guide, we will show you how to register,\ninstall, and set up a Behringer X-DANTE expansion card for your Behringer X32.\nFollow the sections below to get started.<\/p>\n\n\n\n

  1. Registration<\/strong><\/a><\/li>
  2. Installing the card<\/strong><\/a><\/li>
  3. X-DANTE setup and routing<\/a><\/strong><\/li><\/ol>\n\n\n\n

    Warranty Registration<\/h2>\n\n\n\n

    By default, Behringer gives you a 1-year warranty. However, if you register your item on the website within 90 days of purchase, Behringer gives you an additional two years on your warranty. It\u2019s free.<\/p>\n\n\n\n

    <\/div>

    How to Register your Behringer to Get the Full Warranty<\/p>

    If you register your Behringer product within the first 90 days of purchase, you get the full 3-year warranty. Let us explain how.<\/p><\/div><\/div><\/a>\n\n\n\n

    TIP<\/strong>: Everything you purchase from Sweetwater<\/strong> comes with our 2-year Total Confidence Coverage (TCC) warranty<\/a>. However, three years is even better than two, so please register with Behringer today.<\/p>\n\n\n\n

    Installing the card<\/h2>\n\n\n\n

    IMPORTANT: <\/strong>Turn off and disconnect your X32, and also, ground yourself by\ntouching a grounded surface before installing the card.<\/p>\n\n\n\n

    Before installing the card, you first need to check the firmware version that your X32 is currently running. If it\u2019s lower than firmware version 2.0, then you\u2019ll need to update it beforehand. To check, press Setup <\/strong>and then select Global<\/strong>. If it is out-of-date, check out our X32 Firmware Update Guide<\/strong><\/a> for update instructions.<\/p>\n\n\n\n

    1. Loosen the two screws holding the current card in place, which is located in the Slot <\/strong>position on the back of the board.<\/li>
    2. Carefully pull out the existing card, keeping it as straight as possible. Installing and uninstalling a card at an angle can result in damage to the board.<\/li>
    3. Carefully insert the X-DANTE card and push it into place. <\/li>
    4. Once the card is connected, install the two mounting screws to hold the card securely in place.<\/li>
    5. Turn on the X32 and go to the Card tab. If installed correctly, you will see the X-DANTE card listed.<\/li><\/ol>\n\n\n\n\n\n\n\n

      X-DANTE setup and routing<\/h2>\n\n\n\n

      IMPORTANT: <\/strong>Dante only supports wired Ethernet connections. This means that\nWi-Fi control is not possible.<\/p>\n\n\n\n

      Now that you have the card installed, the last\nthing to do is to get everything set up and connected. Depending on your\nspecific setup, you may want to configure your X32 system one way over the\nother, but it\u2019s a breeze no matter how you set it up. Once everything is set\nup, check out Audinate\u2019s great tutorial playlist down below to learn how to use\nthe Dante Controller software.<\/p>\n\n\n\n

      1. Log in to your Audinate account<\/a>. If you don\u2019t have an account yet, create one here<\/a>.<\/li>
      2. Go to the Audinate download page and download Dante Controller<\/a> for your OS. <\/li>
      3. Use an Ethernet cable to connect the X32 to the source (e.g., laptop, network router, digital mixer)<\/em> via the Primary <\/strong>port.<\/li>
      4. Head over to the Config page on the X32. Since a master clock source needs to be chosen for the network, select X-DANTE<\/strong>.
        • Alternatively, you can choose Local <\/strong>to use the X32\u2019s internal clock as the master clock.<\/li><\/ul><\/li>
        • Navigate to the Routing <\/em>page, choose the Card Out<\/strong> tab, and update your expansion card output routing.<\/li>
        • Launch the Dante Controller software and update the routing as necessary. <\/li><\/ol>\n\n\n\n
          \n
          \n
          \n